Description
Hemp Shield Log Home Treatment™— Ultra-low Toxicity, Eco-Friendly. Hemp Shield is a proud manufacturer of the first hemp seed oil containing Wood Finish & Deck Sealer for all wooden products.
INSTRUCTIONS FOR USE —
SURFACE PREPARATION & APPLICATION INSTRUCTION
Hemp Shield™ is a water-reducible hemp oil product designed to penetrate wood, especially decks, and provide excellent durability with no peeling; deterioration of the finish occurs only through erosion. Hemp Shield™ also retards fungal and algae growth as well as controlling blue rot. Hemp Shield™ is recommended for use on any properly prepared wood decking, patios, wood screening, porches, outdoor furniture, steps, railings, plywood structures, and wooden fencing.
State-of-the-art protection for outdoor wood in a truly ‘green’ product.
SURFACE PREPARATION :
Surfaces must be clean, free of all dirt, mildew, loose wood fibres, and other foreign matter.
Surfaces must be structurally sound and completely dry.
Wood moisture content must be below 15% (approximately the same as kiln dried lumber) or the surface must be exposed to dry weather for 3 to 5 days before applying Hemp Shield™.
Previously stained or weathered wood surfaces must be sanded, scrubbed, or otherwise treated to remove loose wood fibers, dirt, mildew, chalky residues, waxes, oils from exotic and pressure treated wood, shiny new wood (Mill Scale) and other foreign materials.
We do not recommend applying Hemp Shield to wood where a glossy finish remains. These previous finishes will prevent Hemp Shield from working since it cannot penetrate into the wood.
To use Hemp Shield on wood that retains a coat of the previous finish it may be necessary to remove the existing finish with blast media such as walnut shells, dry ice, or other media. In some cases sanding may be required.
COVERAGE:
In ASTM testing, Hemp Shield records coverage of 324 sq. ft./gal. at 1 mil dry film thickness. In actual use, Hemp Shield products typically form a dry film thickness of 0.5 mil, increasing coverage to approximately 450-650 sq. ft. Because Hemp Shield is a penetrating oil, coverage will vary due to species, porosity, cell structure, rate of growth, weathering, age, and other factors.
MILDEW :
Remove mildew by washing the wood with a solution of 1 part liquid bleach and 3 parts water.
Do not add detergents or ammonia to the bleach/water solution.
Apply the solution and scrub the affected area.
Allow the solution to remain on the surface for at least 10 minutes.
Rinse thoroughly with water and allow the surface to dry completely before applying Hemp Shield™.
LEAD WARNING — IF YOU SCRAPE, SAND, OR REMOVE OLD PAINT FROM ANY SURFACE, YOU MAY RELEASE LEAD DUST. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.
Wear an NIOSH approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start removing any finish, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on: www.epa.gov/lead
APPLICATION INSTRUCTIONS :
Hemp Shield™ can be applied by brush, roller, foam brush, and airless or conventional sprayers.
Stir thoroughly before using.
Avoid applying late in the day, when dew or condensation is likely to form, or when rain is threatening.
Apply when the temperature (surface, product, and air) is between 50°F (10°C) minimum, 100°F (37°C) maximum, and at least 5° above the dew point.
Relative humidity should not exceed 85%.
Do not apply to new or restored wood if the moisture content exceeds 15% or the surface is wet to the touch.
All water based decking stains have a potential to lap; to reduce lapping tendencies, do not apply in direct sunlight or when the wood feels hot to the touch. A very light misting of water, just enough to tighten the grain on the surface, will also reduce any lapping tendencies.
Do not apply to any surface that feels wet to the touch.
Use at package consistency — do not thin.
Do not over-apply — excess material can cause uneven drying, discoloration, surface residue, and peeling. During application, Hemp Shield will appear milky, but will clear as it penetrates. Once the Hemp Shield has cleared, remove any excess material with a rag, dry brush, or roller.
SPRAYING LARGE AREAS :
When spray applying over areas such as decks, patios, siding, shakes, shingles or fencing, it is recommended that Hemp Shield™ be back rolled or back brushed with a dry brush or roller, to ensure even penetration and remove excess material.
OVER-WATER AND HIGH HUMIDITY INSTALLATIONS ABOUT DECK SEALER:
Hemp Shield Wood Finish and Deck Sealer™ for over-water structures such as docks, swimming floats and walkways, and in chronic high humidity environments, the entire plank, including the edges and end grain, must be sealed. Before assembly, pre-drill and treat all screw holes with Hemp Shield to protect the wood exposed by drilling the holes. Complete treatment is essential for best performance, especially tannin control, in high moisture environments.
IMPORTANT INFORMATION ABOUT DECK SEALER:
Hemp Shield Deck Sealer and Wood Finish™ works very differently from other outdoor wood protectants. Instead of forming a urethane or acrylic shell over the wood’s exterior, the hybrid waterborne hemp oil in Hemp Shield Deck Sealer and Wood Finish™ penetrates the deck sealer, working from within to protect and nourish your outdoor wood. Hemp Shield Deck Sealer and Wood Finish™
When using Hemp Shield™, it is important not to over-apply, as excess material, if allowed to remain, can cause slow, uneven drying, discoloration, sticky residue, and peeling.
Hemp Shield™ should be applied continuously from one end of a plank to the other. Immediately after application, Hemp Shield™ may appear slightly milky, but it will quickly become clear as it penetrates. Any excess material remaining on the surface at this point should be dry-brushed, dry-rolled, or wiped with an absorbent cloth. Hemp Shield’s protection is in the wood — it creates a much thinner surface film tham conventional finishes.
Different types of wood will accept varying amounts of Hemp Shield™. This is determined by species, porosity, cell structure, rate of growth, weathering, age, and other factors such as ambient moisture. Let the wood tell you how much Hemp Shield™ to use.
APPLICATION METHOD SPECIFICATIONS & OTHER INFORMATION WOOD SEALER:
Brush — Use a nylon/polyester bristle brush or foam brush.
Roller — Use 1/8″ to 3/8″ nap synthetic roller cover. A shorter nap performs better when applying Hemp Shield™.
Airless Sprayer — Pressure: 2000 PSI; Tip: .013″ – .017″
Conventional Sprayer — Pressure: 40-60 PSI; Fluid Pressure: 20 PSI; Tip: 704/FX
Clean Up: Use 1-2 teaspoons of “Ivory” type soap to 1 gallon of water. Clean-up should begin immediately after the application is complete or when stopping for ten minutes or more. To avoid spontaneous combustion during temporary storage, soak soiled rags and waste immediately after use in a water-filled, closed metal container.
First Aid: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. If affected by inhalation or spray mist, remove to fresh air. If swallowed, do not induce vomiting. Call a physician immediately.
TERMS AND CONDITIONS OF SALE
APPLICABLE CONTRACT PROVISIONS
These terms and conditions, together with any other documents, which Hemp Shield LLC ("Seller") has attached hereto as part of the contract (the "Agreement"), are the sole and complete contract between Buyer and Seller in respect to the Products and supercede all prior oral and written understandings. Seller rejects those provisions of any previous order, offer, or other communication from Buyer, which are additional to or different from the terms hereof. Neither Seller’s delivery of the Products nor any other action at any time on the part of Seller shall constitute acceptance of such additional or different terms. Buyer shall be bound by all of the terms of this Agreement when Buyer accepts this Agreement by any statement, act or course of conduct which constitutes acceptance under applicable law, including failure to object in writing hereto within a reasonable time and acceptance of delivery of the Products.
DESCRIPTION OF PRODUCTS
The products subject hereto are those described in Appendix A (the “Products”). Seller may substitute reasonably equivalent materials, components or units for any one or more of the products based upon its then current formulation. The only specifications which are a part of this Agreement are the written specifications listed in the “Specifications” section of the Technical Data Sheet, if any, made available to Buyer by Seller regarding the Products. All other material describing the Products is intended only to provide Buyer with a general idea about the Products and may not be relied upon as a “basis of the bargain” for this Agreement.
PURCHASE PRICE AND TERMS OF PAYMENT
A. Price: The price for the Products shall be the price agreed upon between the parties. Typographic or other clerical errors in stated prices are subject to correction.
B. Credit and Terms of Payment: Unless otherwise provided, payment in full is due thirty (30) days from invoice date. Seller may alter or revoke credit terms at any time without notice.
C. Buyer’s Financial Condition; Insecurity: If, in Seller’s sole judgment, Buyer’s financial condition or any other circumstance causes Seller to be insecure with respect to Buyer’s performance of any obligation under this Agreement, Seller may accelerate and demand immediate payment of any amounts owed Seller, cancel this Agreement and suspend performance.
D. Sales and Similar Taxes; Shipping Costs; Insurance: The purchase price does not include sales, use, excise or similar taxes or any shipping, delivery or insurance costs. Seller will invoice Buyer for any such amounts incurred by Seller on behalf of Buyer.
E. Late Payment Fee: Any amount not paid when due will be subject to a late payment fee computed daily at a rate equal to one and one-half percent (1.5%) per month or the highest rate permissible under applicable usury law.
SHIPMENT, DELIVERY AND TERMS OF ACCEPTANCE
A. Shipment: Seller will package the Products for domestic shipment in accordance with standard commercial practices. All shipments shall be delivered by Seller or Seller's agents to the Buyer’s designated point of delivery at the Buyer’s expense unless otherwise agreed by Seller in writing. The carrier shall be deemed to be Buyer’s agent, and Buyer shall make all claims with respect to damage in transit against the responsible carrier.
B. Title to Products, Risk of Loss: Title to and all risk of loss concerning the Products shall pass to Buyer upon delivery to a common carrier, or to any private carrier designated by Buyer, for shipment to Buyer. Buyer’s rejection of any Products shall not shift such risk until the Products are returned to Seller, freight prepaid, pursuant to Seller’s written authorization. Buyer hereby expressly acknowledges and agrees that Section 2-510 of the Uniform Commercial Code shall not apply to this Agreement.
C. Delivery Schedule: Any delivery dates specified in this Agreement are estimates only, based on prevailing conditions as of the date hereof, and Seller’s failure to meet the same shall not be deemed a breach of this Agreement.
D. Force Majeure: Seller shall not be liable to Buyer for any delay or failure of delivery or of any other performance caused in whole or in part by any contingency beyond Seller’s reasonable control, including, without limitation, acts of any government or any agency or subdivision thereof or shortage of or inability to secure labor, fuel, energy, raw materials, supplies or machinery at reasonable prices or from regular sources.
E. Inspection and Acceptance: Buyer shall inspect all shipments upon arrival and shall notify Seller in writing of any shortages or other failures to conform to this Agreement which are reasonably discoverable upon arrival.
F. Cancellation or Modification of Order: This Agreement cannot be cancelled or modified after Buyer’s acceptance or after the Products become Seller’s work-in-process, whichever occurs first, except at Buyer’s expense for all damages incurred by Seller due to such cancellation or modification.
WARRANTIES, LIMITATIONS OF WARRANTIES, DISCLAIMER OF WARRANTIES AND LIMITATION OF DAMAGES
A. Limited Warranty to Buyer: If Seller provides Technical Data Sheet(s) to Buyer with respect to one or more of the Products, Seller warrants that those Products, when supplied to Buyer in production quantities, will conform to any specifications listed in the “Specifications” section of the most recent Data Sheet provided by Seller with respect to that Product. Unless otherwise agreed in writing, Seller’s sole obligation in the event of a breach of any warranty shall be to repair or replace the defective Product or to refund all payments made by Buyer to Seller for such Product, at Seller’s option.
B. Notification of Defect and Time Limitations: Buyer must notify Seller in writing of any alleged defect in the Product within ten (10) days after discovery thereof but not later than 180 days from receipt. Buyer shall identify the defect in such manner and provide such documentation as a Seller reasonably may require. Buyer shall return any alleged defective Product to Seller, F.O.B. Seller’s manufacturing plant, upon receipt of written request from Seller. Buyer must bring any lawsuit against Seller with respect to any Product within 180 days after providing notification of defect under this subparagraph or, if no notice is provided, within 180 days after such notice was required to be provided under this subparagraph.
C. LIMITATION OF WARRANTY: THE LIMITED WARRANTY SET FORTH IN SUBPARAGRAPH a ABOVE SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN ABUSED, ALTERED, MODIFIED, USED IN A MANNER NOT ORIGINALLY INTENDED, USED AFTER THE SHELF LIFE OF THE PRODUCT, OR STORED OR APPLIED IN A MANNER CONTRARY TO SELLER’S WRITTEN INSTRUCTIONS.
D. DISCLAIMER OF WARRANTIES: EXCEPT AS EXPRESSLY PROVIDED IN SUBPARAGRAPH a ABOVE, SELLER MAKES NO REPRESENTATION OR WARRANTY WITH RESPECT TO THE PRODUCTS SOLD HEREUNDER, AND SELLER DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND FREEDOM FROM PATENT INFRINGEMENT. NO AGENT, EMPLOYEE OR REPRESENTATIVE OF SELLER HAS ANY AUTHORITY TO BIND SELLER TO ANY AFFIRMATION, REPRESENTATION OR WARRANTY EXCEPT AS STATED IN THIS AGREEMENT.
DEFAULT
In the event of any default by Buyer, Seller may exercise any and all rights and remedies provided by law. Buyer shall pay to Seller all reasonable costs of collection, including reasonable attorney’s fees, incurred by Seller in collecting any amounts owing by Buyer hereunder.
APPENDIX A — PRODUCTS
- Hemp Shield Log Home Treatment Deck Sealer — Clear
- Hemp Shield Log Home Treatment Deck Sealer — Cedar
- Hemp Shield Log Home Treatment Deck Sealer — Chesnut
- Hemp Shield Log Home Treatment Deck Sealer — Hickory
- Hemp Shield Log Home Treatment Deck Sealer — Redwood
- Hemp Shield Log Home Treatment Deck Sealer — Cobblestone Gray
